ArcGIS Enterprise SDK

IMSegmentation3 Interface

Provides access to additional linear referencing operations on polylines.

Name |
Description | |
---|---|---|

CalculateNonSimpleMs | Redefines the non-simple Ms to be values obtained from interpolation of surrounding defined Ms, or extrapolation of Ms. | |

CalibrateByDistance | Calibrates Ms of existing vertices using new Ms from the input points and the shortest path distances along the polyline between those points. The update method is given as a combination of esriGeometryUpdateMEnum values. | |

CalibrateByMs | Calibrates Ms of existing vertices using new Ms from the input points and existing Ms along shortest paths between those points. The update method is given as a combination of esriGeometryUpdateMEnum values. | |

ExtrapolateMs | Extrapolates the Ms at one or both ends of the geometry based on the M interval between the fromIndex and the toIndex. | |

GetDistancesAtM | Returns an array of distances along the polyline at which is located the specified M. If the geometry's M's are monotonic along the geometry then the array will only have one element. | |

GetMsAtDistance | Returns M values at the distance along the geometry. An array of one or two Ms is returned. Two Ms can be returned if the given distance is exactly at the beginning or ending of a part. | |

GetNormalsAtM | Returns a geometry bag of line segments corresponding to the normal at the locations along the geometry where the specified M occurs. | |

GetPointsAtM | Returns a multipoint geometry corresponding to the locations along the geometry where the specified M occurs. | |

GetSubcurveBetweenMs | Returns a polyline geometry corresponding to the subcurve(s) between the fromM and the toM. | |

GetSubcurveBetweenMsEx | Returns a polyline geometry corresponding to the subcurve(s) between the fromM and the toM values. The 'details' arguments are composed of esriMCurveRelationEnum values. | |

InsertMAtDistance | Sets the M value at the given distance along the geometry; creates a point at that distance if no point exists there. | |

InterpolateMsBetween | Generates Ms by linear interpolation of segment distances for all vertices in the range [start+1, end-1]. | |

MMax | The maximum M value. | |

MMin | The minimum M value. | |

MMonotonic | A value indicating whether Ms are monotonic, and if so, whether they are ascending or descending. | |

MMonotonicity | A combination of esriMonotinicityEnum values that describes all trends in M values over the length of the curve. | |

MultiplyMs | Multiplies all the M values by a factor. | |

OffsetMs | Offsets all the M values by an offset value. | |

OrientByMs | Re-orients the curve to make Ms non-decreasing, if possible. | |

QueryFirstLastM | Returns the first and last defined M value for the curve. | |

ReverseMsOrder | Reverses the order of the Ms along the geometry. | |

SetAndInterpolateMsBetween | Sets the Ms at the beginning and the end of the geometry and interpolates the M values between these values. | |

SetMsAsDistance | Sets the M values to the cumulative length from the origin of the geometry. | |

SetMsAsDistance2 | Sets Ms on vertices as scaled and offset distances from the input origin as measured along the polyline. Shortest path distances from the origin are used. Optionally ignores distances between parts of the polyline. | |

UpdateAllMsByMs | Sets Ms on vertices as scaled and offset M distances from the input origin as measured along the polyline based on the existing M's. Shortest path distances from the origin are used. Optionally ignores distances between parts of the polyline. | |

UpdateMsByDistance | Updates Ms along the shortest path between the specified endpoints. The interpolation ratio is determined by the input ms and euclidean distance along that path. The update method is given as a combination of esriGeometryUpdateMEnum values. | |

UpdateMsByMs | Updates Ms along the shortest path between the specified endpoints. The interpolation ratio is determined by the existing ms along that path and the input ms. The update method is given as a combination of esriGeometryUpdateMEnum values. |

Interfaces | Description |
---|---|

IMSegmentation2 | Provides access to additional linear referencing operations on polylines. |

IMSegmentation | Provides access to members for defining an M-based linear coordinate system on a polyline or polygon. |

IMCollection | Provides access to members that control operations on M-aware multipoints, polylines, polygons and multipatches. |

Classes | Description |
---|---|

Polyline | An ordered collection of paths; optionally has measure, height and ID attributes. |