Adding linear events by creating a starting station and then offset

Mit der Location Referencing-Lizenz verfügbar.

Using stationing to locate measures

Stationing is the fundamental system of measurement used for pipeline layout and construction. Stations are reference points that are placed along the horizontal measurement of a route centerline or a baseline at some regular interval. Generally, the distance between two adjoining stations along a route is 100 feet. The first station located at the beginning of the baseline is 0+00, and the next station located 100 feet from it is 1+00. Therefore, a station number of 10+34.05 denotes 1,034.05 feet (10*100 + 34.05) from the starting station.

The station numbers increase from west to east or south to north based on the cardinal direction of the overall pipeline. For pipeline projects, a starting reference station is first established; then all distances along the route centerline are measured from that point location. You can add event data to routes by entering station numbers in the Line Events tool interface. The station data is translated to routes and measures for storage.

You can use the stationing data as an input for adding linear events in the following three scenarios:

• Create a starting or base station on the route and enter the station values as an offset from that station.
• Identify a starting or base station on the route and enter the station values as an offset from that location.
• Use the preexisting stations on the route to calculate or enter the measures in the form of station values.

Locating measures by creating a starting or base station on the route

You can use this method when no stations are present on the route. You'll create a starting or base station on the route and specify the stationing values for measures. The measures will be located at an offset from the starting station. As shown in the example below, a starting station (yellow star) is temporarily located, and a station value is provided. The event's start or end location is then identified using an offset distance (in station values) from the starting station. When the new linear events are created using this method, the stationing data is translated to routes and measures for storage.

1. Open ArcGIS Event Editor and, if prompted, sign in to your ArcGIS organization.
2. Click the Edit tab.
3. In the Edit Events group, click the Line Events button .
4. Click the Network drop-down arrow and choose the network that will serve as a source linear referencing method (LRM) for defining the input measures for the new linear events.

   The network is an LRS Network published as a layer in the Event Editor. You can specify the LRS Network to be used as the LRM for defining the start and end measures of the new linear event. Event Editor also accepts measures in a network or LRM other than the one with which the linear event layer is associated.

   The new event will be associated with the routes (route IDs) from the LRS Network with which the event location intersects.

5. Choose the name of the line feature on which the events will be located using one of the following options:
   • Click the drop-down arrow to choose the line name in the Line Name text box.
   • Click the Select a Line on the Map tool and select the line from the map.

   

   Tipp:

   If the selected line is not in the active view of the map, click the Zoom to the line extent or center on the line start or end point on the Map button to refresh the map display to zoom in to the entire extent of the selected line.

   The line is highlighted in light blue. The arrow at the end shows the direction of calibration of the line.

6. In the From section, click the Method drop-down arrow and choose Starting station and offset.

   

   The Starting Station section appears.

   

7. In the Starting Station section, for Station, click the Select a Location on the Map tool and select the location of the starting station on a route in the map.

   • A yellow star indicates the location of the starting station on a route in the map.
   • The linear referencing method (LRM) measure equivalent to the location is displayed in Reference. For example, if the LRM is milepoint, the number of miles at that location is displayed.
   • Type the station number in the Stationing text box.
   • The Route Name text box is populated in the From section.

8. Type the station value of the starting station.
9. In the Starting Station section, click the drop-down arrow and choose the units for station values.
10. In the Starting Station section, click the Direction drop-down arrow and choose the direction.

    This selection indicates the direction the station values increase along the route compared to the direction of calibration of the route.

11. In the From section, provide the station number to allot the From measure for the event using one of the following options:
    • Click the Select a Location on the Map tool , and click a location on the selected route. The station number is derived from the route.
    • Type the station number.

    The From measure location will be placed at an offset from the starting station.

    A green cross symbol appears at the selected location on the map.

12. In the To section, click the Method drop-down arrow and choose an offset method.

    You can use separate methods to locate the From and To measures of the events. For example, by locating the To measure of the event using an intersection offset as shown in Step 6.

    A red cross symbol appears at the selected location on the map.

13. Choose the date that will define the start date of the events by doing one of the following:
    • Type the start date in the Start Date text box.
    • Click the Start Date drop-down arrow and choose the start date.

    The start date defaults to today's date, but you can choose a different date using the date picker.

14. Choose the date that will define the end date of the events by doing one of the following:
    • Type the end date in the End Date text box.
    • Click the End Date drop-down arrow and choose the end date.

    The end date is optional, and if it is not provided, the event remains valid now and into the future.

15. Choose from the following data validation options to prevent erroneous input while characterizing a route with linear events:
    • Retire overlaps—The system adjusts the measure and start and end dates of existing events in such a way that the new event does not cause an overlap with respect to time and measure values.

      

    • Merge coincident events—When all attribute values for a new event are exactly the same as an existing event, and if the new event is adjacent to or overlapping the existing event in terms of measure values, the new event is merged into the existing event and the measure range is expanded accordingly.

      

    • Prevent measures not on route—This data validation option ensures that the input measure values for from measure and to measure values fall in the minimum and maximum range of measure values on the selected route.
16. Click Next.

    The tab showing the attribute set for the events appears.

    

    Hinweis:

    You can use the check boxes to add data for specific events in the attribute set. No records are added for events that are not checked.

17. Choose attribute information for the new event using the following options:
    • Type the attribute information for the new event in the tables defined by attribute sets.
    • Click the Copy Attribute Values button and click a route on the map to copy event attributes from another route.

    Event Editor uses a default attribute set on the Edit tab. You can modify the attribute set to create custom attribute sets or use the administrator-configured attribute set.

    Hinweis:

    Coded values, range domains, and subtypes are supported when configured for any field in the Attribute-Value table.

18. Use the following options to access more information on the attribute set:
    • Check the Show network name check box to show the LRS Network associated with the selected event layer.
    • The list of attributes in the tables defined by attribute sets can be from more than one event layer. If you want to identify the source event layer for each attribute, check the Show layer names check box.
    • Checking the Go to the next measure upon save check box results in prepopulating the From measure value using the To measure value of the present section to continue the event creation process.
19. Click Save.

    The new linear events are created and appear on the map. A confirmation message appears at the lower right once the newly added line events are saved.

After a linear event has been successfully created, you have the following two options to continue characterizing the route:

• Click New Edit to clear all the input entries in the widget and restore the default values from the geodatabase to the table.
• Click Next Edit to retain all the existing entries in the widget and the attribute set for convenience and for quick editing of similar characteristics.