Skip To Content

Adding point events using existing stations on a route

Mit der Location Referencing-Lizenz verfügbar.

Use stationing to locate measures

Stationing is the fundamental system of measurement used for pipeline layout and construction. Stations are reference points that are placed along the horizontal measurement of a route centerline or a baseline at some regular interval. Generally, the distance between two adjoining stations along a route is 100 feet. The first station located at the beginning of the baseline is 0+00, and the next station located 100 feet from it is 1+00. Therefore, a station number of 10+34.05 denotes 1,034.05 feet (10*100 + 34.05) from the starting station.

Placement of stations along a centerline

The station numbers increase from west to east or south to north based on the cardinal direction of the overall pipeline. For pipeline projects, a starting reference station is first established, and all distances along the route centerline are measured from that point location. You can add event data to routes by entering station numbers in the Point Events tool interface. The station data is translated to routes and measures for storage.

You can use the stationing data as an input for adding point events by using these three scenarios:

  • Create a starting or base station on the route and define the station values as offsets from that station.
  • Identify a starting or base station on the route and define the station values as offsets from that location.
  • Use the existing stations on the route to calculate or define measures in the form of station values.

Using the existing stations on the route to calculate the measures

You can use this method when stations exist on the route. The measures are calculated using the location and values of the existing stations. This functionality is available only for the LRS Networks that contain a stationing event layer.

In the following example, there are three existing stations on the route. Stations A, B, and C have station values of 00+00.00, 50+00.00, and 100+00.00. respectively. The stations increase in value following the direction of calibration of the route, which is from left to right on the map. The measures on the route are located by taking these three stations into consideration. Therefore, the measure of the event (station value 82+18.27) is located nearer to the third station—that is, 100+00.00 between the second and the third stations.

Locating a point event using an offset from the existing stations

  1. Open ArcGIS Event Editor and, if prompted, sign in to your ArcGIS organization.
  2. Click the Edit tab.
  3. In the Edit Events group, click the Point Events button Punktobjekte.

    The Add Point Events widget appears.

    Add Point Events widget

    If there are no editable point event layers, the widget is unavailable.

  4. Click the Event Layer drop-down arrow and choose an event layer to edit.
  5. Click the Network drop-down arrow and choose the network that will serve as a source for providing the measure for the new event.
    • The widget accepts an LRS Network as a source to identify the location for adding the new point event. However, when the new point event data is being stored in the database, the app performs an internal translation of measures to always store the measure value in the linear referencing method (LRM) of the LRS Network with which the event is registered.
    • The Network value can be a published LRS Network layer.
  6. Type a route name in the Route Name text box on which the new event measure will be based.
    Tipp:

    You can also click the Select a Route on the Map button Route auf der Karte auswählen to select the route on the map.

  7. Hinweis:

    If a message appears that is related to acquiring locks, the need to reconcile, or not being able to acquire locks, Pipeline Referencing conflict prevention is enabled.

    Learn more about conflict prevention in ArcGIS Event Editor.

  8. In the Location section, click the Method drop-down arrow and choose Stationing.
    Choosing the Stationing method
  9. In the Location section, click the drop-down arrow and choose the units for station values.
  10. In the Location section, provide the station number using one of the following options to allocate the measure for the new point event:
    • Type the station number in the Station text box.
    • Click the Select a Location on the Map tool Position auf der Karte auswählen and click a location on the selected route. The station number is populated in the Station text box.

    The measure location will be placed at an offset from the starting station.

    A red x appears at the selected location on the map.

  11. Choose the date that will define the start date of the events by doing one of the following:
    • Type the start date in the Start Date text box.
    • Click the Start Date drop-down arrow and choose the start date.
    • Check the Use route start date check box.

    The start date defaults to today's date, but you can choose a different date using the date picker.

    Hinweis:

    If you configured your Event Editor instance to not allow dates before the start date of the route, and you provide a date before the start date of the selected route in Start Date, a warning message appears alerting you to choose a date on or after the start date of the selected route.

  12. Choose the date that will define the end date of the events by doing one of the following:
    • Type the end date in the End Date text box.
    • Click the End Date drop-down arrow and choose the end date.
    • Check the Use route end date check box.

    The end date is optional, and if it is not provided, the event remains valid now and into the future.

  13. Click Next to view the Attribute Value table.

    This table contains all the attributes of the event layer.

  14. Provide attribute information for the new event in the table.
    Tipp:

    You can click the Copy Attribute Values button Attributwerte kopieren and click an existing point event belonging to the same event layer on the map to copy event attributes from that point.

  15. Check the Show network name check box to show the LRS Network with which the selected event layer is associated.
  16. Click Save.

    A confirmation message appears at the lower right once the newly added point event is saved. The new point is created and appears on the map.

After an event has been successfully created, you have the following two options to continue characterizing the route:

  • Click New Edit to clear all the input entries in the widget and restore the default values from the geodatabase to the attribute table.
  • Click Next Edit to retain all the existing entries in the widget and the attribute table for the convenience of quick editing of similar characteristics.